Jump to content
Sign in to follow this  
SeaNo180

Ultimate Turbo Reference guide for Nissans.

Recommended Posts

Make and model: Nissan Silvia S13

Size of engine: CA18DET, 1.8L

Modifications to the car: 1mm oversize forged pistons, stainless manifold, full 3inch exhaust, kn pod filter, RB20 throttle body, butterflies removed from inlet manifold, 650x250x90mm bar and plate hyperflow intercooler, Remapped ECU - TUNED BY DR DRIFT, Bosch 040 Fuel pump, GTR injectors, Z32 AFM

Type of turbo: GT28RS

Trim of turbo: ??

Rear Exhaust housing: 0.64

When does vehicle begin boost: 2000rpm

When does vehicle reach full boost and what PSI: 3500rpm, 22psi

Does the vehicle have Cams? if so; CA16DE inlet cam, Stock exhaust cam, Growly Adjustable cam gears

What brand: Stock Nissan

What lift/duration etc: 248/8.5mm lift

Max power achieve at what boost: 244rwkw @ 21psi

 

scan0024.jpg

Share this post


Link to post
Share on other sites

Make and model: nissan silvia s13

Size of engine:SR20DET

Modifications to the car: 3 inch exhaust gutted cat, FMIC, hks panel filter in standard air box,turbo smart boost contoller

Type of turbo: ATP turbo

Trim of turbo:unknown

Rear Exhaust housing unknown

When does vehicle begin boost:3,00rpm (ish)

When does vehicle reach full boost and what PSI:approx 4,200rpm, 15psi

Does the vehicle have Cams? no non turbo cams very soon to bring the lag down a tiny bit

power 200rwkw maybe doin injectors and microtech than hittin the dyno

Share this post


Link to post
Share on other sites

Youre dreaming mate...stock S13 ECU and Injectors? More like 160rwkw...................

Share this post


Link to post
Share on other sites

Make and model: e30 320i

Size of engine: 2.0

Modifications to the car: sr20det conversion, lsd, front mount, gt28rs, microtech lt10, 550 injectors, walbro pump

Type of turbo: gt28rs

Trim of turbo: nfi

Rear Exhaust housing: .64

When does vehicle begin boost: 2000

When does vehicle reach full boost and what PSI: 3250 16psi

Does the vehicle have Cams? if so; yes

What brand: camtech drop in camshaft

What lift/duration etc:

Max power achieve at what boost: 195rwkw @ 16psi

 

 

Share this post


Link to post
Share on other sites

Make and model:2002 s15 spec r gt adm

Size of engine:2L

Modifications to the car:axexi pfc, avcr, bosch fuel pump, hks 740cc injects, trust exhaust , trust cooler, z32 afm

Type of turbo: 2871r

Trim of turbo:56t

Rear Exhaust housing:0.64

When does vehicle begin boost:2100rpm

When does vehicle reach full boost and what PSI:3800rpm spike to 18.5 settle at a constant 17.7/5psi

Does the vehicle have Cams? if so;

What brand:Tomei Pon Cams

What lift/duration etc:11.5 256dur

Max power achieve at what boost:244.0 @ 17.7 psi

 

few areas need attention just to help smooth out the graph a lil, will be goin for a 2nd run next week to see if there was a change

 

dyno-1.jpg

Share this post


Link to post
Share on other sites

Make and model:S13 Silvia

Size of engine:1.8 ca18det

Modifications to the car: 3" turbo back, gtr front mount

Type of turbo: t25

Trim of turbo: .64 i think

Rear Exhaust housing:

When does vehicle begin boost: early

When does vehicle reach full boost and what PSI:

Does the vehicle have Cams? if so;

What brand:

What lift/duration etc:

 

Max power achieve at what boost:130.9 @ 10psi

 

car is stock apart from front mount + exhuast at Morpowa's new dyno

Share this post


Link to post
Share on other sites
Youre dreaming mate...stock S13 ECU and Injectors? More like 160rwkw...................

 

just to let you and others know.

 

i have two mates s13 redtop SR's making 200rwkw with just T28's standard injecs/standard AFM.

 

tuned by morpowa.

Share this post


Link to post
Share on other sites

Just to let you know, the stock S13 injectors will not make 200rwkw.

Share this post


Link to post
Share on other sites

lol. they are stock injectors. what more can i say.

 

one makes 196rwkw and the other makes 201rwkw.

 

so yeh the stock injectors do make 200. thanks

Share this post


Link to post
Share on other sites

They must be the 2 missing Magic S13s ive heard about...you sure that aint rwph?...Bit more realistic.....considering no one else seems to be making that power on STOCK S13 injectors and T28s...on reptops..............my previous car included where the stock S13 injectors were maxed at 170rwkw?.....

Share this post


Link to post
Share on other sites

Make and model:98 S14a

Size of engine: sr20det

Modifications to the car:full zorst, fmic, fuel pump, ECU, AVCR

Type of turbo: stock non BB T28

Trim of turbo:

Rear Exhaust housing:

When does vehicle begin boost:2500k

When does vehicle reach full boost and what PSI:3500k @ 13psi

Does the vehicle have Cams? if so; No

What brand:

What lift/duration etc:

Max power achieve at what boost: 186rwkw 13psi

Share this post


Link to post
Share on other sites

Make and model: 99 S15 Silvia

Size of engine: SR20DET

Modifications to the car: Predator Motorsports Radiator/Intercooler Kit, Microtech LT10s, HKS 550cc Injectors, Sard Regulator, Bosch Intank Pump, Custom 3in dump and 3 inch exhaust, xforce low mount manifold.

Type of turbo: GT2876R

Trim of turbo: No idea

Rear Exhaust housing: 0.86

When does vehicle begin boost: Unsure, maybe 3000?

When does vehicle reach full boost and what PSI: Again unsure, maybe like 5000? 21psi.

Does the vehicle have Cams?; No.

What brand: N/A

What lift/duration etc: N/A

Max power achieve at what boost: 352.4HP/262.7KW at 21psi.

dynosheet.jpg

Share this post


Link to post
Share on other sites

^^^ whats your injector duty cycle at man, thats big power for the size of Inj, and big boost spike as well!

Share this post


Link to post
Share on other sites

110%+!....Haha...considering 550s will flow around 100hp each.....

Share this post


Link to post
Share on other sites

Dunno. Yeah the boost spike i need to manage somehow. I'll let you know how much 550s can take when I put my cams and whay not in.

Share this post


Link to post
Share on other sites

Make and model: S14a 200sx

Size of engine: 2L

Modifications to the car: 3" full exhaust, FMIC, GT2871R, 040 pump, gizzmo IBC, Gktech manifold

Type of turbo: GT2871R

Trim of turbo:

Rear Exhaust housing: 0.64

When does vehicle begin boost: 2000rpm

When does vehicle reach full boost and what PSI: 4000rpm

Does the vehicle have Cams? if so; stock

What brand:

What lift/duration etc:

Max power achieve at what boost: 188.7rwkw @ 10psi

Share this post


Link to post
Share on other sites

Make and model: 91 SIL80

Size of engine: 2L

Modifications to the car: 3" full exhaust, FMIC, hypergear atr28g1, 040 pump, turbo tech boost controler, 480cc jdm s15 injectors

Type of turbo: Hypergear atr28g1

Trim of turbo:

Rear Exhaust housing: 0.86

When does vehicle begin boost: 60kph??? not sure on rpm

When does vehicle reach full boost and what PSI: 100kph.... spikes to 17 then sits at 15 psi

Does the vehicle have Cams? if so; stock

What brand:

What lift/duration etc:

Max power achieve at what boost: 178kw atw at 15psi........ on a dr.drift base tune. fine tuning to come. was running mega richcammo_dyno_run_001.JPG

Share this post


Link to post
Share on other sites

Thats a really good result mate, same as my setup once its done...didnt wanna wind anymore boost into it? Did you use the stock valve springs with those cams?

Share this post


Link to post
Share on other sites

Make and model: Nissan S15 200sx

Size of engine: 2.0L

Modifications to the car: Lots, all the pieces to make it run right :)

Type of turbo: GT2871R

Trim of turbo: .64

When does vehicle begin boost: 2200

When does vehicle reach full boost and what PSI: 4700

Does the vehicle have Cams? if so: Yes 2x 256's, Both cam gears.

What brand: Tomei

What lift/duration etc: 256, 11.5

Max power achieve at what boost

 

232.1atw at 12 PSI, 272.4atw at 18psi

Edited by JPZ200

Share this post


Link to post
Share on other sites

yeh VCT snapped on me, got the both adjustables there. But its like a creepy climb gets to about 9-10pounds and then the the rest comes in at around 4300-4700

 

Plus car is starting to ping, when I use 18 pound and then drop down to 15 pounds, so taking it to Belgarage, since CRD do not road tune/test cars after a dyno tune. I think its the airtemp thats wrong and timing going near 42 degrees.

Share this post


Link to post
Share on other sites

Make and model: S15 2000 Spec R

Size of engine: 2L

Modifications to the car: FPC D-jetro, Greddy Plenum, Hypertune Throttle Body, Sard 800cc injectors, big fuel lines, Splitfire Ignition, Walbro intake pump and two external 044 bosch pumps, 6 boost manifold, CP pistons, Eagle H rods...think thats about it...

Type of turbo: garrett GT3076R

Trim of turbo: ?

Rear Exhaust housing: ?

When does vehicle begin boost:2500

When does vehicle reach full boost and what PSI: 4200 @ 25psi on ROO16

Does the vehicle have Cams? if so; yes

What brand: HKS Step 2 + HKS Valve Springs

What lift/duration etc: ?

Max power achieve at what boost: 421.7HP @ 25 psi on ROO16

 

dyno1.jpg

 

 

 

 

 

Paul

Edited by zombie_s15

Share this post


Link to post
Share on other sites

Make and model: nissan silvia ca18det

Size of engine: 1.8 L

Modifications to the car: 3" zorst turbo back, speedlab remap, fmic, 535cc sard injectors, rb25 afm

Type of turbo: 2871 BB

Trim of turbo: 52 trim

Rear Exhaust housing: .64

When does vehicle reach full boost and what PSI: 3800-4200 17psi

Does the vehicle have Cams? if so; exhaust cam on inlet side, stock exhaust cam.

What brand: n/a

What lift/duration etc: n/a

Max power achieve at what boost: 235 rwkw 17psi

 

With cam gears i hope to hit full boost a bit earlier and bring the mid range up fair bit

Edited by useless

Share this post


Link to post
Share on other sites

Thought I already put my results in here, but apparently it was a different thread.

So here they are:

 

Make and model: Nissan 180SX

Size of engine: 2.0L

Modifications to the car: Nismo 740CC, Nistune ECU, CAMS, Cam Gears, 3.5" Turboback Exhaust, 6 Boost manifold, 38mm Turbosmart gate, profec b ebc, fmic.

Type of turbo: GT2871

Trim of turbo: 52 trim

Rear Exhaust housing: .64

When does vehicle reach full boost and what PSI: 4500 at 22 PSI

Does the vehicle have Cams? if so; 264 11.5 Intake, 272 11.5 Exhaust Cams

What brand: Greddy

What lift/duration etc: 264 11.5 Intake, 272 11.5 Exhaust Cams

Max power achieve at what boost: 358.2RWHP at 22 PSI

 

scan0005.jpg

scan0006.jpg

Share this post


Link to post
Share on other sites

http://hardtuned.net/forums/index.php?showtopic=382765'>http://hardtuned.net/forums/index.php?showtopic=382765

 

Make and model: Nissan S14 SR20DET

Size of engine: 2.0L

Modifications to the car:

POWERTUNE GT3071 T2 .64 internal gated turbo kit

POWERTUNE low mount tune length 4 into 1 merge collector manifold

POWERTUNE Intake Pipe

POWERTUNE Intercooler kit

Braided Earls Turbo oil and water lines

Aeromotive Fuel Pressure Regulator

POWERTUNE 3inch turbo back exhaust system

POWERTUNE Topfeed 1000cc fuel rail kit

Bosch 023 fuel pump

Haltech E8

 

Type of turbo: GT3071 T2 internal gate

Trim of turbo: 56 trim

Rear Exhaust housing: .64

Does the vehicle have Cams? if so; STANDARD CAMS

 

Max power achieve at what boost: 257.6rwkw with 98 OCTANE 277.4rwkw on 24psi with E85

 

98 octane

lastscan2.jpg

 

lastscan1.jpg

 

E85

dynosheet-1.jpg

 

http://hardtuned.net/forums/index.php?showtopic=382765

Share this post


Link to post
Share on other sites

Make and model: Nissan Cefiro 1988

Size of engine: 2.0L

Modifications to the car: GTR injectors, BLITZ front mount, Walbro fuel pump, STATUS remap, Z32 AFM, BLITZ exhaust

Type of turbo: HKS 25/35

Trim of turbo: duno

Rear Exhaust housing: duno

Does the vehicle have Cams? STANDARD CAMS

Max power achieve at what boost: 216.8 kw on 17psi, full boost by 3600rpm

Share this post


Link to post
Share on other sites

Make and model: s15 sr20det unopened engine in s13

Size of engine: 2.0L

Modifications to the car: supporting mods nismo 740's, z32 afm, greddy valve springs, copy sump, jjr exhaust manifold modded to suit 44mm tial, 3 inch exhaust, trust 400x300x100 tube and fin intercooler, 40mm china radiator, trust oil cooler, splitfires, old blitz dsbc, bosch 044 and surge tank, s15 pfc.

Type of turbo: 3071

Trim of turbo: 56T 71mm compressor .5ar housing, 84T 60mm GT30 turbine .63 housing

Rear Exhaust housing: .63 non gated

When does vehicle begin boost: dunno

When does vehicle reach full boost and what PSI: 20psi@3600

Does the vehicle have Cams? if so; yep

What brand: Unigroup spec camtechs,

What lift/duration etc: 255 11.5 in 260 12.0 ex

Max power achieve at what boost: 285rwkw@21psi on ultimate

 

dyno done on r888 semi's, spark breaking down so bit of a rough curve

 

12092009096.jpg

Share this post


Link to post
Share on other sites

Thanks mate,

 

I was a bit surprised with it myself.

 

Now i just want to drive the thing! Damn unregistered track nugget...

Share this post


Link to post
Share on other sites

Awesome stuff Dave! Should be fantastic on the track with a curve like that. I dare say your only issues will be traction with that sort of midrange.

 

Thought I'd post my former setup for anyone interested:

 

180SX Build 005.jpg

 

Make and model: S13 SR20DET

Size of engine: 2.0L

Modifications to the car: Nismo 740's, Z32 afm, Tomei RAS, alloy radiator, oil cooler, Hybrid FMIC, HKS SS Manifold, HKS 40mm External 'gate, 3 inch exhaust with ceramic cat

Type of turbo: HKS T300

Turbo Trim: .6a/r, 3" inlet, 0.63a/r exhaust housing

When does vehicle begin boost: ??

When does vehicle reach full boost and what PSI: 1.4bar @ low 4's

Does the vehicle have Cams? if so; No

Max power achieve at what boost: 241rwkw @ 1.4 bar on 98. Ignition was breaking down hence the shape of the curve at high rpm

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

×