Jump to content

Pat180

Silver Member
  • Content count

    89
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Pat180

  • Rank
    Newbie
  • Birthday 06/21/1984

General Info

  • Location
    Australia SA
  • Car Type
    Nissan Silvia
  • Car Model
    180sx
  1. Shed clean out, off my 180sx, have been unused for about 8 years. No issues when using them. To be honest not sure what brand the front suspension is (or even if it's the stock suspension). $100 for all 4 pieces.
  2. Car stalling

    Secondary to me being a jackarse, I've just discovered that the vacuum line in the pic below is actually not connected to anything... does anyone know where it should be heading to?
  3. Car stalling

    It came off my intercooler pipe on the hot side (Trust v-spl cooler, it has an attachment for a BOV) so I just took it off and plugged that up with a stopper and the vacuum line that was running to it I just removed (it was part of a 3 way connector that I changed to 2).
  4. Just fixing the old girl up after being defected and have removed my EBC (profec B spec II). Now, I'm having a problem with the car continually stalling when idling and was wondering if it was due to me not having hooked something back up that I should have. In the pic there's this thing on the turbo side of the engine bay with two nipples, both with covers on them (1&2). As I didn't install the EBC I wasn't sure if they needed some form of vacuum line to them. Also, at (3) there are two nipples pointing straight up that have nothing going to them. Just wondering if I'm missing something. Also, on a side note, I have removed my BOV and it's now running without one, I'm not sure if that would affect it. Thanks for your help.
  5. Driver's side mirror

    Cheers for the replies, Unley Glass did it for $30, need to tkae your mirror off though and drop it into them for 24 hours as they glue it on for you. (was for a 180)
  6. Hey team, anyone know of a place to get a mirror cut for my driver's side mirror? Just some cheapo cash job. Best I've found is $50, making it cheaper just to buy the whole unit, cheers, Patrick
  7. Hey guys, after some: - stock s13 rear suspension - drivers side mirror - little plastic part of the dash that goes under the steering wheel (have my EBC very well attached to it currently) just to borrow, cheers
  8. What is this?

    Nice, thanks. Can anyone point me in the direction of what needs to be hooked up to where?
  9. Hey team, was removing my EBC today due to getting defected, and came across this in the left side of the engine bay near where the EBC was mounted. Now I'm not actually sure what it's for, but more importantly I wanted to know if I need to connect anything up to it now that the EBC's gone. There's two nipples with covers on them at the moment (one pointing up, one pointing to the firewall) and I also noticed there's two nipples below it (pointing up in the picture) that are uncovered... In removing the EBC, which is a profec b, I disconnected the two hoses that were running to the solenoid and joined them together (so the vacuum hose now runs from the actuator to some triple connection point) thanks for your help.
  10. Hey team, I'm after a well recommended workshop to chuck the 180 on a dyno and tune a Profec B with a gt28rs. Had it done ages ago at a reputable joint, but after fiddling around with it myself recently found I can make it more responsive and reach about the same boost level without spiking, but rather than tune it myself on the roads would rather someone else do it... so, anyone very happy with their profec b's performance/confident in a workshops ability to tune them? Don't bother bad mouthing places either, just after positive experiences. cheers, Patrick.
  11. Hey team, few months ago I remember a local selling Nissan badges for 180 bonnets etc for about $15, lived out north I think... had mine pinched recently in the school holidays. Anyone know who was selling them? Cheers, Patrick
  12. The Adelaide Casino

    yeah you're right, more small cards in the deck i.e. 32 less tens, means the dealer is more likely to make a total than bust... also, the dealer hits on soft 17 e.g. A+6, A+2+4, and is likely to make a greater total. I always tell customers they're better off playing blackjack...
  13. The Adelaide Casino

    I've been a dealer/inspector at the cas for the last 5 years, the invitation to the grange room upstairs could be true. if you bet consistently large amounts over a period of time, even in a day, a VIP staff member MAY give you a temporary card to get in upstairs, but you have to keep up a massive turnover to become a permanent member. if your mate only had 100 to gamble with in the beginning there's no chance he'll keep that membership... and as for the $0-100,000 claim, definite BS. Biggest BJ table is $100 min and $5000 max and roulette max on a straight up is $400. I suppose you should never let the truth get in the way of a good story...
  14. 180sx Headlight Issue

    negative on the indicator stalk being the issue... even when i manually move the contacts etc the LHS high beam stays on... so it's somewhere further down the track, where will i find the relays? and is there a specific 'high beam' fuse? i had a look at the LH & RH H/LAMP fuses, not damaged at all...
  15. Hey guys, was just after an opinion of those more electronically minded than myself... My LHS headlight is stuck on high beam permanently, so when i turn my lights on, the LHS has only high beam and the RHS is normal. I have changed the bulbs recently, as I thought this could be the problem but to no avail. I noticed last night when I was driving that at times the LHS light would switch from high beam to normal for a short period of time, then back again, was thinking perhaps there is a loose wire somewhere... Hopefully someone can point me in the right direction.
×